11-03-2012, 11:45 PM | #21 |
Junior Member
Join Date: Nov 2012
Posts: 2
|
Windows 8 DisplayLink issue
Hello,
Hello, I recently upgraded to Windows 8 Pro, and I have the WUSB to HDMI DisplayLink Adapter from Cables Unlimited a.k.a. Warpia, IOGear GUWAVKIT2, and a few other names that it sells under. The last WUSB driver I tried to use is version 14.2.174.8, with no luck. When we plugin the USB adapter, it tries to plug-n-play, but doesn't complete like it did with Windows 7, as there were about 7 Device Connect sounds, and the screen would flash a couple times as it initialized. With Windows 8, there are only 2 Device Connect sounds, with no screen flash. If the device is left connected, the computer blue screens after a few minutes. Hopefully one of the vendors are working on a new driver for Windows 8. We are using the latest DisplayLink software. Thanks for reading, and for any help. Mike |
11-04-2012, 02:17 AM | #22 |
Junior Member
Join Date: Nov 2012
Posts: 2
|
Windows 8 DisplayLink issue - reattempt
Hello, I just made another attempt at loading the WUSB drivers and DisplayLink software. I uninstalled both the driver and software, and rebooted. Then I put the DisplayLink USB dongle into the USB port on the computer. Everything installed except for the USB Root Hub for it with a yellow exclamation symbol and an Error 31. When I tried Updating The Driver manually, it would go online to look for one, but would come back to say that it had the best driver on the computer already, despite the yellow triangle symbol. Then I tried reloading the Windows 8 compatible DisplayLink software again. It would start to load, then it seemed like it would quit in the middle of the install. I'm used to clicking Finish at the end of any install which would tell me that it was successful, but that doesn't happen. However, it shows two entries in the Programs and Features list (DisplayLink Core Software and DisplayLink Graphics). The DisplayLink tray icon does not appear at all. Then when I load the WUSB driver for it, that loads fine, but still it does not work. Each time I try to load the driver, it wants to update the firmware on the USB dongles, but I have been skipping that part because I know that they are updated. When the dongle is connected at the PC, the green light flashes quickly for a few seconds, then goes steady, then flashes rapidly again for a few seconds, then shows steady, and does this over and over with no result. I have seem the PC blue screen if I leave the dongle in there too long. Thanks for any help and suggestions. Mike
|
11-04-2012, 11:03 AM | #23 |
Junior Member
Join Date: Nov 2012
Posts: 2
|
Hello,
I did exactly as mentionned in http://kb.displaylink.com/334, at least 6, 7 times. Without any luck. |
11-04-2012, 11:31 AM | #24 |
Junior Member
Join Date: Nov 2012
Posts: 2
|
I also have the problem with out Laptop Lenovo X1 Carbon. As Windows 8 is installed (with USB 3.0 driver) I only installed the Lenovo USB 3.0 Dock driver and the new Display Link 7.0M2.
Only a few seconds the external display appeards, than the signal is gone... After ever new plug-in the same. I already tried every step/hints on this forum-page. Nothing helps. Do you have any hints to a stable connection to the USB 3.0 dock? We need the Notebooks urgently in office... Thanks a lot! |
11-05-2012, 12:10 PM | #25 | ||
Senior Member
Join Date: Feb 2009
Posts: 1,561
|
Quote:
Quote:
|
||
11-05-2012, 12:11 PM | #26 | |
Senior Member
Join Date: Feb 2009
Posts: 1,561
|
Quote:
Someone on here did have an issue with the X1 and updating the BIOS helped. Could you try this and see if it helps solve the issue? Wim |
|
11-05-2012, 12:32 PM | #27 |
Junior Member
Join Date: Nov 2012
Posts: 2
|
Yes, I already updated BIOS from Lenovo support page and tried the new drivers. The first time monitors show a few seconds, now nothing happens, if I connect the dock.
|
11-05-2012, 01:34 PM | #28 |
Junior Member
Join Date: Nov 2012
Posts: 1
|
Screen Flashing
I'm having the same issues as well. I had done an upgrade to Windows 8 when it first started. After having other issues with the upgrade, I wiped the hard drive and did a clean install of Win 8 Pro. I installed the latest 7.0 M2 driver (downloaded from the DisplayLink website), hooked up the monitor, rebooted the machine when prompted to, and the screens began flickering on after reboot. Here is a video of what is happening: http://goo.gl/OT2ph. Sorry for the poor audio, but you should be able to get the gist.
|
11-05-2012, 01:57 PM | #29 |
Junior Member
Join Date: Nov 2012
Posts: 1
|
Win 8 - DisplayLink drivers not working
Have ImationLink USB adapter, worked just fine with Win 7, after upgrade to Win 8 no video signal, audio connection seems to work. Uninstalled and reinstalled DisplayLink software and driver several times with no effect. Solution?
|
11-06-2012, 03:03 AM | #30 |
Junior Member
Join Date: Nov 2012
Posts: 6
|
Similar flashing or black screen issue
Hi, I am running windows 8 on a new Lenovo w530. I have installed, uninstalled, reinstalled drivers etc countless times (including all the ways suggested in this thread) and have had no luck). When wanting to extend my display I get the flashing screen. If I instead duplicate my display my second screen goes black, but has a windows arrow in the centre and my primary screen switches to low resolution, but the flashing ceases. If I switch my secondary screen to off (ie only keep my primary display) then my resolution of my primary screen goes back to normal and the secondary screen goes blank.
Log from the displaylink support tool is attached below (I ran the tool while the primary screen was flashing) Any help suggestions would be much appreciated. |
|
|